look wat sana brought

Discussion in 'General Scooter Discussion' started by lol, Jan 1, 2008.

  1. lol

    lol New Member

    Messages:
    964
    lol, Jan 1, 2008
    #1
  2. shiny red

    shiny red New Member

    Messages:
    1,224
    v nice :D and very usefull
     
    shiny red, Jan 1, 2008
    #2
  3. lol

    lol New Member

    Messages:
    964
    very usefull to undo clutch nut and vario to min job
     
    lol, Jan 1, 2008
    #3
  4. capri dave

    capri dave Active Member

    Messages:
    5,076
    nice bit of kit there ;)
     
    capri dave, Jan 1, 2008
    #4
  5. lol

    lol New Member

    Messages:
    964
    i dont think its the top make but it is a great kit well pleased with it my dad said it was 250 down 150 in makcese tool ware house
     
    lol, Jan 1, 2008
    #5
  6. Burns

    Burns Active Member

    Messages:
    1,486
    Rides:
    Aprilia sr50
    the air ratchits are violent as hell! be carefull cos ive had them snag on me a few times! can snap your wrist like bending toffee :rofl:

    nice kit though :cool:
     
    Burns, Jan 1, 2008
    #6
  7. lol

    lol New Member

    Messages:
    964
    iv youed it loads of times it seam ok it dont spin fast at all
     
    lol, Jan 1, 2008
    #7
  8. kyle1b1

    kyle1b1 New Member

    Messages:
    5,191
    because your trying to loosen and titghten with it. that not what their for is just for winding them in and out.
     
    kyle1b1, Jan 1, 2008
    #8
  9. lol

    lol New Member

    Messages:
    964
    i undo nut with it seems ok
     
    lol, Jan 1, 2008
    #9
  10. MiNoR cOnFuSiOn

    MiNoR cOnFuSiOn Administrator Staff Member

    Messages:
    14,276
    Rides:
    et2 monster
    if your using them on the fariator/clutch remember to wind it hand tight with a rachet then give it a VERRY QUICK hit with the impact wrench.. it takes a couple clicks to make 150nm an you only need to tighten it to 52 ish..
     
    MiNoR cOnFuSiOn, Jan 1, 2008
    #10
  11. SMF_12

    SMF_12 New Member

    Messages:
    1,048
    who's sana ? ;)
     
    SMF_12, Jan 1, 2008
    #11
  12. Jamie

    Jamie Active Member

    Messages:
    5,370
    Rides:
    xt660x, 200sx s14a
    santas little helper
     
    Jamie, Jan 1, 2008
    #12
  13. MiNoR cOnFuSiOn

    MiNoR cOnFuSiOn Administrator Staff Member

    Messages:
    14,276
    Rides:
    et2 monster
    dont mind him.. dont celebrate crimbo the jahova :D
     
    MiNoR cOnFuSiOn, Jan 1, 2008
    #13
  14. Jamie

    Jamie Active Member

    Messages:
    5,370
    Rides:
    xt660x, 200sx s14a
    :msn1:

    is he one of them annoying people that knock on your door on sundays telling you the earth is going to end in 2 weeks :confused:arc:
     
    Jamie, Jan 1, 2008
    #14
  15. MiNoR cOnFuSiOn

    MiNoR cOnFuSiOn Administrator Staff Member

    Messages:
    14,276
    Rides:
    et2 monster
    nah, he nocks on your parts sayin "want anythin from bike it?" LOOOOOOOOOL
     
    MiNoR cOnFuSiOn, Jan 1, 2008
    #15
  16. SMF_12

    SMF_12 New Member

    Messages:
    1,048
    you slagwhorebitch

    what ya orderign from me this month then :w00t:
     
    SMF_12, Jan 1, 2008
    #16
  17. lol

    lol New Member

    Messages:
    964
    i do the nut up hand tight and just let it tight it up about ten times and it seams ok
     
    lol, Jan 1, 2008
    #17
  18. MiNoR cOnFuSiOn

    MiNoR cOnFuSiOn Administrator Staff Member

    Messages:
    14,276
    Rides:
    et2 monster
    too tight, crank will split.

    these are no longer used by quickfit as they snapped one in 10 bolts fitted. you have to know how tight your doing it as too tight on anything will FUCK it completly
     
    MiNoR cOnFuSiOn, Jan 1, 2008
    #18

Share This Page