Search Results

Search Again
Page 1 of 3
  1. Xylon
    Post

    Make clutch engage at LOWER RPMs.

    Dandruff37: I think the scooter was entering the powerband before the clutch even engaged.
    Post by: Xylon, Nov 12, 2013 in forum: Maxiscooter Tuning
  2. Xylon
    Post

    Make clutch engage at LOWER RPMs.

    12g
    Post by: Xylon, Nov 12, 2013 in forum: Maxiscooter Tuning
  3. Xylon
    Post

    Make clutch engage at LOWER RPMs.

    Those are stock rollers. Note that (I don't know if this is true of other rollers) have a brass ring inside to give them their weight. Anyway, I...
    Post by: Xylon, Nov 12, 2013 in forum: Maxiscooter Tuning
  4. Xylon
    Post

    Make clutch engage at LOWER RPMs.

    OK, I found the problem. The rollers were very worn, and had large flat spots. Original diameter: 20mm Honda specified minimum: 19.5mm Actual...
    Post by: Xylon, Nov 10, 2013 in forum: Maxiscooter Tuning
  5. Xylon
    Post

    What's this sound

    Opened up the transmission this morning. Turned out I didn't need to remove the floor panel. I could get it of by taking all the panels off the...
    Post by: Xylon, Sep 17, 2013 in forum: The Workshop
  6. Xylon
    Post

    How do I check if my starter motor is knackered? Can I use a multimeter?

    hang on, if the motor was drawing too much power then the fuse would already have blown. Have you checked your fuses? You can test fuses with a...
    Post by: Xylon, Sep 16, 2013 in forum: The Workshop
  7. Xylon
    Post

    How do I check if my starter motor is knackered? Can I use a multimeter?

    Well connect the battery to the starter motor through a (13 AMP?) fuse
    Post by: Xylon, Sep 16, 2013 in forum: The Workshop
  8. Xylon
    Thread

    Transmission cover hot?

    I noticed the transmission cover gets quite hot (feels about 50'C). Is this normal?
    Thread by: Xylon, Sep 16, 2013, 1 replies, in forum: The Workshop
  9. Xylon
    Post

    What's this sound

    OK I just verified anti-clockwize is the normal direction of engine rotation. Actually I think the sound is coming from inside the transmission...
    Post by: Xylon, Sep 16, 2013 in forum: The Workshop
  10. Xylon
    Post

    Reminder to all UK riders

    aw, thanks I didn't know that
    Post by: Xylon, Sep 14, 2013 in forum: Scooter Related News
  11. Xylon
    Post

    Lifan Jet 50cc engine worn down under warranty?

    25mph is dangerously slow because people will be trying to overtake you even on a 30mph road. Your vehicle is in DANGEROUS condition and there is...
    Post by: Xylon, Sep 14, 2013 in forum: The Workshop
  12. Xylon
    Post

    What mpg are you all getting?

    Look on here: http://www.fuelly.com/motorcycle/ This is my scooter: http://www.fuelly.com/driver/xylon/ps125i
    Post by: Xylon, Sep 14, 2013 in forum: General Scooter Discussion
  13. Xylon
    Post

    Lifan Jet 50cc engine worn down under warranty?

    No it's not right. Any 50c should be able to do at least 30mph on a flat road. If it's still under warranty they should fix it. If they won't...
    Post by: Xylon, Sep 14, 2013 in forum: The Workshop
  14. Xylon
    Post

    What's this sound

    Try the link again. The server was advertising the wrong mime type. The engine seems to run fine but I must admit I didn't notice that sound...
    Post by: Xylon, Sep 14, 2013 in forum: The Workshop
  15. Xylon
    Post

    What's this sound

    Won't be able to check it for a couple of weeks because I see in my Haynes: `Discard the gasket and O-ring as new ones must be used on...
    Post by: Xylon, Sep 14, 2013 in forum: The Workshop
  16. Xylon
    Post

    What's this sound

    yes yes OK
    Post by: Xylon, Sep 14, 2013 in forum: The Workshop
  17. Xylon
    Post

    What's this sound

    4t 125cc Fuel injected Liquid cooled
    Post by: Xylon, Sep 13, 2013 in forum: The Workshop
  18. Xylon
    Thread

    What's this sound

    Just curious, what's this sound I hear when I turn my engine anti-clockwize using a socket on the variator nut:...
    Thread by: Xylon, Sep 13, 2013, 11 replies, in forum: The Workshop
  19. Xylon
    Thread

    Valve adjustment locknut tightness

    I couldn't find a torque setting for the valve adjustment locknuts so I tightened them to 7nm since they're only 8mm nuts. Is that OK?
    Thread by: Xylon, Sep 12, 2013, 1 replies, in forum: The Workshop
  20. Xylon
    Post

    Be aware of 'undercover' police cars

    Thanks a lot for the warning
    Post by: Xylon, Jun 16, 2013 in forum: Scooter Related News
Showing results 1 to 20 of 54 Next >
Search Again
Page 1 of 3